VanThanBK · Tube and Pipe Routing
Supported process skid
Release R001 · 13 part definitions · 13 tubes · 2026-09-11T04:23:56.356301+00:00
Dimensions in mm; angles in degrees. End A is the feed start in the bend table; End B is the tail. Print notch PDFs at 100% and check the 100 mm scale bar. Saved setups contain measured or operator-entered compensation; verify the first part on the actual machine.
Parts and manufacturing files
| Part / rev | Name / notes | OD × wall | Cut length | Qty | Bender setup | Files |
|---|
TP00001
r1 | Pipe 60.3x3.2-1 (3)
| 60.3 × 3.2 mm | 275.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00002
r1 | Pipe 60.3x3.2-2 (4)
| 60.3 × 3.2 mm | 435.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00003
r1 | Pipe 60.3x3.2-1 (4)
| 60.3 × 3.2 mm | 230.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00004
r1 | Pipe 60.3x3.2-2
| 60.3 × 3.2 mm | 473.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00005
r1 | Pipe 60.3x3.2-3 (2)
| 60.3 × 3.2 mm | 1146.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00006
r1 | Pipe 60.3x3.2-4 (2)
| 60.3 × 3.2 mm | 243.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00007
r1 | Pipe 60.3x3.2-1
| 60.3 × 3.2 mm | 328.50 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00008
r1 | Pipe 60.3x3.2-2 (1)
| 60.3 × 3.2 mm | 488.50 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00009
r1 | Pipe 60.3x3.2-1 (1)
| 60.3 × 3.2 mm | 230.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00010
r1 | Pipe 60.3x3.2-2 (2)
| 60.3 × 3.2 mm | 473.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00011
r1 | Pipe 60.3x3.2-3
| 60.3 × 3.2 mm | 1146.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00012
r1 | Pipe 60.3x3.2-4
| 60.3 × 3.2 mm | 243.00 mm
0 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
TP00013
r1 | Pipe 21.3x2.3-1 (1)
| 21.3 × 2.3 mm | 1521.37 mm
2 bends | 1 | Unassigned (zero compensation; steel density)
Steel density assumed | Bend CSV
Shop PDF |
Supports
Support assemblies are counted separately from tubes and flow fittings.
| Support | Pipe OD | Qty | Materials | Dimensions / parts |
|---|
| Split clamp | 60.3 mm | 2 | rubber, steel | Preset 3403064; Mount rod, H 112 mm; Axial width 23 mm, band 2 mm; Liner 2 mm; Rod dia 10 mm; 12 parts |
| U-bolt support | 60.3 mm | 2 | steel | Fabricated; Mount foot, H 100 mm; U-bolt dia 10 mm, H 120.3 mm; Foot 80 x 60 mm; 9 parts |
| Pipe shoe | 60.3 mm | 4 | ptfe, steel | Fabricated; Mount none, H 105.15 mm; guided; base 160 x 80 mm; Saddle 120 mm; 6 parts |
| Block clamp | 21.3 mm | 1 | polypropylene, steel | Preset Group 3 / SP / DP / AS-M6; Mount none, H 21 mm; Block 50 x 36 mm, axial 30 mm; Bolt centres 33 mm; 6 parts |
Changes since previous release
A changed source-body revision requests review even when the nominal centerline is unchanged. This is not a tolerance-based geometry-equivalence test.
| Part | Change | Before | After |
|---|
| TP00001 | added | | 1 |
| TP00002 | added | | 1 |
| TP00003 | added | | 1 |
| TP00004 | added | | 1 |
| TP00005 | added | | 1 |
| TP00006 | added | | 1 |
| TP00007 | added | | 1 |
| TP00008 | added | | 1 |
| TP00009 | added | | 1 |
| TP00010 | added | | 1 |
| TP00011 | added | | 1 |
| TP00012 | added | | 1 |
| TP00013 | added | | 1 |
| FITTINGS | bom | 0 | 36 |
| SUPPORTS | bom | 0 | 9 |
31 files listed in the manifest. Unregistered model bodies are outside this tube package. Register supported imported tubes with Recognize Tube.